03 Ford 6 0 Diesel Icp Sensor Replacement Youtube 2003 ford 6.0 diesel powerstroke or a vt365 icp sensor replacement. yoooo, whats going on yall. welcome back. here on this dumpy trucky, we had to replace th. Replacing the icp sensor on an early 04 truck. the sensor is located under the turbo y pipe area. tool seen in video ordered off of freedomracing overall.
Parts Accessories Car Truck Parts 6 0l 03 04 Injector Control How to replace icp sensor on 6.0 powerstroke in 1 minute | 2005 2007location, tools, ect.ford 6.0l (2004 2007) icp sensor ford 6.0l part number: 4c3z 9f838. 6.0l power stroke diesel 03 6.0 icp sensor replacement i was having cold start issues with my '03 6.0 powerstroke then the check engine light came on. i ran the code and it said that i had a bad icp sensor. i researched this code, bought a new sensor from the local ford dealership and was planning to replace it. First step, after you determine that you need to replace this sensor and or connector, is to remove the air filter, degas jug, ficm, and the rear stud on the intake manifold. you'll then see this pretty much: icp sensor with interfering components removed. zoomed in some. use a long right angle pick to take loose the icp sensor connector. Remove 10mm bolt from passenger side and one from drivers side. also remove 13mm bolt from drivers side and slide heat shield onto bell housing. 5. slide insulating sleeve off the icp sensor. 6. remove electrical connector from icp sensor. lift tab with finger and slide off being careful not to remove connector seal. 7.
2006 Ford 6 0 Diesel Icp Sensor Location First step, after you determine that you need to replace this sensor and or connector, is to remove the air filter, degas jug, ficm, and the rear stud on the intake manifold. you'll then see this pretty much: icp sensor with interfering components removed. zoomed in some. use a long right angle pick to take loose the icp sensor connector. Remove 10mm bolt from passenger side and one from drivers side. also remove 13mm bolt from drivers side and slide heat shield onto bell housing. 5. slide insulating sleeve off the icp sensor. 6. remove electrical connector from icp sensor. lift tab with finger and slide off being careful not to remove connector seal. 7. By liam plunket 1 july 202326 september 2023. on to the point: the icp (injection control pressure) sensor on a 2003 6.0 powerstroke is typically located on the high pressure oil pump cover, at the front of the engine, near the turbocharger. the 6.0 powerstroke engine is known for its robust performance and reliability, powering heavy duty. 6.0l power stroke diesel how to replace the icp sensor 03 6.0 is there anywhere i could info, pics, or a procedure on how to change out the icp sensor in the back of the engine. i searched but could not find a procedure. i did see you need a 1 1 16 crows foot. dealer wants over $500 to replace it, i would like to.
How To Replace Icp Sensor On 6 0 Powerstroke In 1 Minute 2005 2007 By liam plunket 1 july 202326 september 2023. on to the point: the icp (injection control pressure) sensor on a 2003 6.0 powerstroke is typically located on the high pressure oil pump cover, at the front of the engine, near the turbocharger. the 6.0 powerstroke engine is known for its robust performance and reliability, powering heavy duty. 6.0l power stroke diesel how to replace the icp sensor 03 6.0 is there anywhere i could info, pics, or a procedure on how to change out the icp sensor in the back of the engine. i searched but could not find a procedure. i did see you need a 1 1 16 crows foot. dealer wants over $500 to replace it, i would like to.
Comments are closed.