How To Replace And Install A Bathroom Sink Attach the drain assembly. fit the drain into the drain hole in your sink, fixing it in place with plumber’s putty and the retaining nut under the sink. connect the p trap to the drain assembly, ensuring it aligns properly with the drainpipe in the wall. this might require cutting the pipe to length for a precise fit. How to install a bathroom sink. a few tricks and tips to make your bathroom installation a whole lot easier. see how to connect the pipes and fittings to the.
:max_bytes(150000):strip_icc()/8_IMG_3767-56a4a2753df78cf772835b72.JPG "How To Replace And install A bathroom Vanity And sink")
How To Replace And Install A Bathroom Vanity And Sink 4. apply caulk to the sink flange and press it onto the drain. take the circular metal flange that fits into the basin of the sink and turn it upside down. slowly squeeze a bead of silicone caulk around the underside of the flange. then, turn it over and place it in the drain of the sink basin. Attach the drain’s tailpiece to the bottom of the sink. make sure to install it with the accompanying gasket. if your model doesn’t come with a gasket, seal it with silicone caulk. reattach the p trap, water lines, and any other hardware, like a pop up drain. seal the connections with silicone caulk. Attach the sink clips to the underside of the vanity top to hold the sink in place. assemble the bathroom faucet and drain on the sink before you attach it to the vanity. place the plastic gasket on the faucet. then, while holding the faucet from underneath, screw on fastening nuts. Remove the old vanity or pedestal sink. enlist a helper for this part. cut around the old sink or vanity with a utility knife to separate it from the drywall or tile. remove any screws or bolts holding the vanity to the wall. pull the existing vanity or sink away from the wall and set it aside. paint or patch the wall if needed.
How To Install A Bathroom Sink A Basic Guide Attach the sink clips to the underside of the vanity top to hold the sink in place. assemble the bathroom faucet and drain on the sink before you attach it to the vanity. place the plastic gasket on the faucet. then, while holding the faucet from underneath, screw on fastening nuts. Remove the old vanity or pedestal sink. enlist a helper for this part. cut around the old sink or vanity with a utility knife to separate it from the drywall or tile. remove any screws or bolts holding the vanity to the wall. pull the existing vanity or sink away from the wall and set it aside. paint or patch the wall if needed. Here’s how to do it: mark the vanity’s width above the rough plumbing. for a 36 inch high countertop, mark 34 1 2 inches above the floor for the top of the 2 by 6 brace. use a level to extend this mark across the installation area. draw a second line 5 1 2 inches below the first to indicate the bottom of the brace. Apply a finishing bead of silicone caulk along the top of the sink along the area where it meets the wall and in any gaps. let the silicone caulk dry for at least 24 hours. turn your water supply back on if you turned it off to the whole house, but don’t use the new sink for at least a day. step ten: check for leaks.
Installing Cement Board Bathroom Remodel Part 2 Youtube Here’s how to do it: mark the vanity’s width above the rough plumbing. for a 36 inch high countertop, mark 34 1 2 inches above the floor for the top of the 2 by 6 brace. use a level to extend this mark across the installation area. draw a second line 5 1 2 inches below the first to indicate the bottom of the brace. Apply a finishing bead of silicone caulk along the top of the sink along the area where it meets the wall and in any gaps. let the silicone caulk dry for at least 24 hours. turn your water supply back on if you turned it off to the whole house, but don’t use the new sink for at least a day. step ten: check for leaks.
Comments are closed.