Derale 16 Pass Electra Cool Remote Transmission Cooler Kit 6an Inlets Derale performance, los angeles, ca 800.421.6288 derale in line thermostat switch wiring (see diagram # )4 specifications electric fan rating: 4.8 amps thermostat switch:maximum of 15 continuous amps 1. using the supplied #10 blue ring terminal, attach the negative ( ) wire on the electric fan to a good chassis ground ( ). 2. Transmission cooler part # 12901 12907 dyno cool by derale, los angeles, ca 800.421.6288 derale (continues on page 2) the transmission cooler can be mounted in multiple locations on your vehicle. reference diagram # 2 for possible cooler positions. #1 is the ideal location, #2 is second best and #4 being the last choice.
Derale 17 Row Serise 9000 Trans Cooler Crt There are two options for installing the in line thermostat. 1. cooler inlet installation (see diagram #1) the in line thermostat fitting is provided with a 8an male and female threads. attach the in line thermostat fitting onto the inlet fitting on the oil cooler. install thermostat switch into the adapter fitting, we recommend using a small. Transmission cooler part # 13611 13615 (continues on page 2) the transmission cooler can be mounted in multiple locations on your vehicle. reference diagram # 2 for possible cooler positions. #1 is the ideal location, #2 is second best and #4 being the last choice. note: the cooler core will flow in either direction, there is no specified inlet. 14. disconnect the factory rubber transmission return hose from both ends and remove. one end radiator fitting, other end steel transmission line. see diagram #10 15. install a hose clamp supplied onto the cooler return hose assembly. connect the short hose coming off the 180 degree fitting to the existing transmission line and tighten clamp. see. Using a 1 1 8” open end wrench, tighten fittings. hold the oil cooler assembly in the desired location. using a marker, mark the four hole locations. using a drill and 9 32” drill bit, drill the four mounting holes. using 1 4” 20 bolts, 1 4” washers & 1 4” lock nuts (not supplied) attach the oil cooler assembly.
Derale 25 Row Hyper Cool Remote Transmission Cooler Kit 8an 14. disconnect the factory rubber transmission return hose from both ends and remove. one end radiator fitting, other end steel transmission line. see diagram #10 15. install a hose clamp supplied onto the cooler return hose assembly. connect the short hose coming off the 180 degree fitting to the existing transmission line and tighten clamp. see. Using a 1 1 8” open end wrench, tighten fittings. hold the oil cooler assembly in the desired location. using a marker, mark the four hole locations. using a drill and 9 32” drill bit, drill the four mounting holes. using 1 4” 20 bolts, 1 4” washers & 1 4” lock nuts (not supplied) attach the oil cooler assembly. 2. slide one hose clamp on each end of the supplied hose. 3. using a dab of oil, lubricate each end of the hose and install hose onto the cooler inlets. 1. identify the 4 mounting rods, 4 mounting clips and. 2. one by one, install the 4 mounting rods thru the. ake the 1x1 foam pads supplied, peel off the paper lining &. First things first, position the cooler on your workbench so you can attach its two fittings, install its thermostat switch, and do the very basic wiring so the thermostat switch can turn the fan on and off. thread the aluminum fittings, the two on the left above, onto the fan assembly’s inlet and outlet connectors.
Tech Feature Derale S Hyper Cool Remote Trans Cooler Chevy Hardcore 2. slide one hose clamp on each end of the supplied hose. 3. using a dab of oil, lubricate each end of the hose and install hose onto the cooler inlets. 1. identify the 4 mounting rods, 4 mounting clips and. 2. one by one, install the 4 mounting rods thru the. ake the 1x1 foam pads supplied, peel off the paper lining &. First things first, position the cooler on your workbench so you can attach its two fittings, install its thermostat switch, and do the very basic wiring so the thermostat switch can turn the fan on and off. thread the aluminum fittings, the two on the left above, onto the fan assembly’s inlet and outlet connectors.
Comments are closed.