Dodge Ram Blend Door Actuator Calibration
![dodge Ram Blend Door Actuator Calibration dodge Ram Blend Door Actuator Calibration](https://www.2carpros.com/images/articles/original/bend-door-actuator-4241.jpg)
Dodge Ram Blend Door Actuator Calibration Close, put the vehicle on running (did mine with engine going) put the recirc speed to low, but not off. hold for 10 seconds and release. immediate press and hold again until the light flashes. then release. the light will flash the remainder of the calibration sequence (roughly 20 seconds). Ram year. 2016. engine. 6.4. i own a 2016 ram 3500 tradesmen 6.4, the heater core was replaced and with the heater box out the blend door actuators were replaced. full disclosure we attempted to get the timing of the position correct when we reassembled everything. once back together we performed the door calibration with alfa obd.
![dodge blend door actuator calibration dodge blend door actuator calibration](https://ytimg.googleusercontent.com/vi/532BOHyQhzo/maxresdefault.jpg)
Dodge Blend Door Actuator Calibration Sorry it took me a little bit, i had to make an emergency trip overseas for a few days for work and just got back yesterday. the new dongle (thank you for the heads up on the alternate @jimmy07) came while i was away, so this morning i used it and was able to connect to the hvac module and successfully complete the blend door actuator calibration. Step 1: insert the ignition key and turn it to the on position. then, hit the ‘auto’ button on the temperature control. turn your car off once the controller says auto on its display. step 2: next, go to the fuse box and pull out the fuse for the ac controller system or hvac actuator. Blend door actuator motor calibration. turn ignition key to the on position and turn on the hvac system. move the key to the off position. open hood (bonnet for the rhd guys) and locate fuse #15 in the fuse box next to the battery. remove the fuse and wait 1 2 minutes for any capacitive charges in the system to dissipate. The calibration procedure should take less than 3 minutes to complete. when the front control panel led lights stop flashing, this indicates the calibration procedure has been successfully completed. if led lights remain flashing for longer than 3 minutes, hvac control module has detected a fault with actuator door calibration.
![2003 dodge ram 2500 blend door actuator Location 2003 dodge ram 2500 blend door actuator Location](https://www.2carpros.com/images/question_images/353958/original.jpg)
2003 Dodge Ram 2500 Blend Door Actuator Location Blend door actuator motor calibration. turn ignition key to the on position and turn on the hvac system. move the key to the off position. open hood (bonnet for the rhd guys) and locate fuse #15 in the fuse box next to the battery. remove the fuse and wait 1 2 minutes for any capacitive charges in the system to dissipate. The calibration procedure should take less than 3 minutes to complete. when the front control panel led lights stop flashing, this indicates the calibration procedure has been successfully completed. if led lights remain flashing for longer than 3 minutes, hvac control module has detected a fault with actuator door calibration. There should be 2 actuators behind the radio bezel. 2 more on the passenger side, 1 by the fan, another up in back of the glove compartment. you can see the rod moving if the actuator is good. if you disconnect the rod from the actuator, then work the rod, you can easily hear each door move if it is not broken. Replaced actuator with dorman 604 029 from autozone $28. need to remove cup holder panel and knee panel below steering wheel. getting into position to do this is challenge with feet out passenger side door. remove foot area down vent above gas pedal.
![How To calibrate blend door actuator In 9 Easy Steps How To calibrate blend door actuator In 9 Easy Steps](https://safetyspecial.com/wp-content/uploads/2022/09/door-actuator-1.jpg)
How To Calibrate Blend Door Actuator In 9 Easy Steps There should be 2 actuators behind the radio bezel. 2 more on the passenger side, 1 by the fan, another up in back of the glove compartment. you can see the rod moving if the actuator is good. if you disconnect the rod from the actuator, then work the rod, you can easily hear each door move if it is not broken. Replaced actuator with dorman 604 029 from autozone $28. need to remove cup holder panel and knee panel below steering wheel. getting into position to do this is challenge with feet out passenger side door. remove foot area down vent above gas pedal.
Comments are closed.